Cisco 800 analoq telefon config

Hamiya salamlar.

1. Cisco 800 Seriyasi olan (cisco 881-v (mpc8300))  modelinde mənə analog telefonun config etməyə komək edəsiz 🙂  . 3-6 portlara 4 rəqəmli nömrə olmalı ve onlarda 1-1 zəng ede bilsinler.  (ardi gelecek hele 1 etapdir )

Səs: 0. Bəyənilsin Zəifdir

Baxılıb: 2065 dəfə


Cavablar ( 6 )

  1. Salam,

    avadanligin  “show version” “show running-config” gonderin zehmet olmasa

    eger mexfi melumat varsa(public ip address username ve.s) onlari silin

    Teshekkurler

  2. Router#sh ver

    Cisco IOS Software, C880 Software (C880VOICE-UNIVERSALK9-M), Version 15.2(4)M4, RELEASE SOFTWARE (fc2)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2013 by Cisco Systems, Inc.
    Compiled Thu 20-Jun-13 16:56 by prod_rel_team

    ROM: System Bootstrap, Version 15.1(2r)T3, RELEASE SOFTWARE (fc1)

    Router uptime is 8 minutes
    System returned to ROM by reload at 16:17:09 AZT Thu Mar 5 2015
    System image file is “flash:c880voice-universalk9-mz.152-4.M4.bin”
    Last reload type: Normal Reload
    Last reload reason: Reload Command

    This product contains cryptographic features and is subject to United
    States and local country laws governing import, export, transfer and
    use. Delivery of Cisco cryptographic products does not imply
    third-party authority to import, export, distribute or use encryption.
    Importers, exporters, distributors and users are responsible for
    compliance with U.S. and local country laws. By using this product you
    agree to comply with applicable laws and regulations. If you are unable
    to comply with U.S. and local laws, return this product immediately.

    A summary of U.S. laws governing Cisco cryptographic products may be found at:
    http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

    If you require further assistance please contact us by sending email to
    [email protected].

    Cisco 881-V (MPC8300) processor (revision 1.0) with 498688K/25600K bytes of memory.
    Processor board ID FCZ1733C3WH

    5 FastEthernet interfaces
    2 ISDN Basic Rate interfaces
    1 Virtual Private Network (VPN) Module
    1 Voice FXO interface
    4 Voice FXS interfaces
    1 DSP, 16 Voice resources
    256K bytes of non-volatile configuration memory.
    247464K bytes of ATA CompactFlash (Read/Write)
    License Info:

    License UDI:

    ————————————————-
    Device# PID SN
    ————————————————-
    *0 C881-V-K9 FCZ1733C3WH

    License Information for ‘c880-srst’
    License Level: advipservices Type: Permanent
    Next reboot license Level: advipservices
    Configuration register is 0x2102

    Router#

  3. show running-config -hecne yoxdur. Rutor tezedir. test etmek isteyirem.  Mesele beledir ki baş offisdə E0 portu ilə ats qoşulub. hər filaldada nomrələr var.  HO offiseden fillara 07xxxx ile yiqilir. onlarda bize rutorda 91xx. mes: (91xx HO. 15xx Filal)

    dial-peer voice 91 voip
    description HO
    destination-pattern 91..
    session target ipv4:xxx.xxx.xxx.xxx
    dtmf-relay h245-alphanumeric
    codec g711ulaw
    no vad

    dial-peer voice 715 voip
    description TEST
    destination-pattern 15..
    session target ipv4:10.10.1.200
    dtmf-relay h245-alphanumeric
    codec g711ulaw
    no vad

     

  4. 1 az qeliz mesledir çox config yaza bilməyəcəyəm. ortada ACS + VPN var.

  5. salam.

    Ancaq analog portlara nömrə vermək isteyirsensə.  POTS dial-peer yarat hansı nömrəni isteyirsen ora yönlendir.

    HO dial eləmək üçün topologiyanı bilmək lazım olacaq. məs CUCM varmı? E1 olan Router CUCM-a necə birləşib? (h323 və ya SİP) və s.

  6. Salam Salman bey. CUCM yoxdur.

    Məsələ aydin oldu. Çox sağ olun Ağa muəllim.

Cavab yazın